WEBVTT

1
00:00:00.000 --> 00:00:05.000
♪ Music playing ♪

2
00:00:00.000 --> 00:00:09.080
Hi, I'm Tamiko from Graco. I'm going to show you how to install the Tranzitions 3-in-1

3
00:00:09.080 --> 00:00:13.200
Harness Booster Forward-Facing with a Vehicle Seat Belt. First, we're going to remove the

4
00:00:13.200 --> 00:00:18.440
headrest on the vehicle seat if your vehicle owner's manual allows it. Next, we're going

5
00:00:18.440 --> 00:00:26.440
to make sure that the lower anchors are properly stored. Then we're going to unhook our tether

6
00:00:26.440 --> 00:00:31.160
and put it over the back of the vehicle seat. We're not going to attach it just yet. We're

7
00:00:31.160 --> 00:00:34.919
just going to put it here to make sure that we don't forget it. Make sure your car seat

8
00:00:34.919 --> 00:00:40.439
is flat on the vehicle seat with at least 80% of the base on the vehicle seat. Next,

9
00:00:40.439 --> 00:00:50.459
we're going to expose the forward-facing belt path. Next, we're going to route our vehicle

10
00:00:50.459 --> 00:00:58.580
seat belt through the forward-facing belt path and buckle. Next, we're going to lock

11
00:00:58.580 --> 00:01:04.459
the vehicle seat belt. We're going to pull out slowly and then let the seat belt go back

12
00:01:04.459 --> 00:01:09.339
into the retractor. If I pull on it, it should be locked. Next, we're going to push on the

13
00:01:09.339 --> 00:01:14.779
center of the seat and pull on the seat belt to tighten. As I'm doing this, I'm feeding

14
00:01:14.779 --> 00:01:20.660
the slack back into the retractor. Next, we're going to attach our tether to the vehicle

15
00:01:20.660 --> 00:01:27.900
tether anchor and tighten. Next, we're going to test for tightness. We're going to grab

16
00:01:27.900 --> 00:01:32.260
at the forward-facing belt path and move the seat side to side and front to back. It shouldn't

17
00:01:32.260 --> 00:01:36.540
move more than one inch in either direction. If it does, press down on the center of the

18
00:01:36.540 --> 00:01:45.980
seat and remove more slack. Then, test for tightness again. Now, you can replace your

19
00:01:45.980 --> 00:01:53.540
seat cover. Make sure you put your harness back in front of the seat. Now, you're ready for your

20
00:01:53.540 --> 00:01:58.940
child. Now that your seat is installed, you're ready to buckle her in. You want to make sure

21
00:01:58.940 --> 00:02:06.339
that the harnesses are at or just above her shoulders and that the crotch belt is in front

22
00:02:06.339 --> 00:02:13.779
of but not underneath her body. Gently tighten the harnesses until they're snug and position

23
00:02:13.779 --> 00:02:19.399
the chest clip level with her armpits. You can check the harness for the correct tightness by

24
00:02:19.399 --> 00:02:23.160
pinching the harness. If you can't grab any material, she's ready to go.