WEBVTT

1
00:00:00.000 --> 00:00:05.000
♪ Music playing ♪

2
00:00:00.960 --> 00:00:10.240
Hi, I'm Meredith from Baby Jogger. I'm going to show you how to install your CityTurn convertible

3
00:00:10.240 --> 00:00:17.280
car seat in rear-facing mode using the vehicle seat belt. Before getting in the car, get your

4
00:00:17.280 --> 00:00:24.240
seat ready. First, make sure your tether is stored on the back of the seat. Next, adjust your recline

5
00:00:24.240 --> 00:00:32.080
foot. Move the recline foot to the rear-facing position marked with the blue label. Make sure

6
00:00:32.080 --> 00:00:36.000
it clicks into place. Adjust your recline to one of the three positions and make sure it clicks

7
00:00:36.000 --> 00:00:42.400
into place. Make sure your lower anchor attachment is stored at the front of the seat. Now you're

8
00:00:42.400 --> 00:00:48.080
ready to get in the car. Place your car seat rear-facing in the vehicle and slide the seat

9
00:00:48.080 --> 00:00:53.040
back against the back of the vehicle seat. Make sure that the base of the car seat sits flat on

10
00:00:53.040 --> 00:00:58.880
the vehicle seat and at least 80% of the base is on the vehicle seat. Make sure that your vehicle is

11
00:00:58.880 --> 00:01:03.840
on level ground and check your level indicator to ensure that it is in the correct blue zone based

12
00:01:03.840 --> 00:01:08.879
on your child's age. Squeeze the lever at the front of the seat and rotate the car seat.

13
00:01:12.320 --> 00:01:14.879
Press the gray button to open the rapid lock lock off.

14
00:01:17.040 --> 00:01:19.519
Route the vehicle seat belt through the rear-facing belt path.

15
00:01:20.400 --> 00:01:27.440
Slide the seat belt along the blue line and under the rapid lock lock off. Buckle the seat belt in.

16
00:01:29.440 --> 00:01:31.839
Make sure the seat belt lies flat and is not twisted.

17
00:01:33.279 --> 00:01:38.480
Take the shoulder belt and slide it into the slit at the back of the base. Press down on the center

18
00:01:38.480 --> 00:01:43.519
of the seat and pull on the shoulder belt to remove slack. Feed the slack back into the retractor.

19
00:01:44.080 --> 00:01:45.599
Close the rapid lock lock off.

20
00:01:48.480 --> 00:01:52.720
Test for tightness at the rear-facing belt path. It should not move more than one inch side to side

21
00:01:52.720 --> 00:01:58.080
or front to back. If it does, open the lock off, remove more slack, and then close it again and

22
00:01:58.080 --> 00:02:02.639
test for tightness. Check your level indicator again to make sure it's still in the correct blue zone.

23
00:02:06.720 --> 00:02:09.199
Adjust the headrest to the proper position for your child.

24
00:02:09.199 --> 00:02:14.720
Remove the infant supports if not using. Now you're ready for baby. Check for proper harness

25
00:02:14.720 --> 00:02:19.360
height. Straps should be at or just below your child's shoulders for rear-facing mode.

26
00:02:19.360 --> 00:02:25.600
Buckle your child in and attach the chest clip. Tighten the harness. Move the chest clip to

27
00:02:25.600 --> 00:02:31.279
armpit level. Do the pinch test. You should not be able to pinch any extra slack at your child's

28
00:02:31.279 --> 00:02:35.759
shoulders. Once your little one is properly harnessed, rotate the seat to the rear-facing

29
00:02:35.759 --> 00:02:37.919
position and click it into place.