WEBVTT

1
00:00:00.000 --> 00:00:05.000
♪ Music playing ♪

2
00:00:00.000 --> 00:00:10.800
Hi, I'm Meredith from BabyJogger. I'm going to show you how to install your CityTurn Convertible

3
00:00:10.800 --> 00:00:16.799
Car Seat in rear-facing mode using the lower anchor attachment. Before getting in the car,

4
00:00:16.799 --> 00:00:20.559
get your seat ready. First, make sure your tether is stored on the back of the seat.

5
00:00:22.959 --> 00:00:25.680
Next, adjust the reclined foot to the rear-facing position.

6
00:00:30.240 --> 00:00:36.240
Next, click it into place and make sure the blue label is up. Adjust the recline to one of the

7
00:00:36.240 --> 00:00:40.639
three positions and click it into place. Remove your lower anchor attachment from the storage

8
00:00:40.639 --> 00:00:46.080
location at the front of the seat. Pull the straps and the connectors out of the storage door.

9
00:00:47.439 --> 00:00:52.480
Close the storage door. Now you're ready for the car. Place the car seat rear-facing in your

10
00:00:52.480 --> 00:00:57.599
vehicle. Make sure that the base of the car seat lies flat on the vehicle seat, and at least 80%

11
00:00:57.599 --> 00:01:01.680
of the base is on the vehicle seat. Make sure that your vehicle is on level ground and check

12
00:01:01.680 --> 00:01:05.680
the level indicator to ensure it is in the correct blue zone based on your child's age.

13
00:01:06.480 --> 00:01:09.199
Squeeze the lever at the front of the seat to rotate the car seat.

14
00:01:12.160 --> 00:01:14.720
Press the gray button to open the rapid lock lock off.

15
00:01:16.160 --> 00:01:19.440
Take your lower anchor attachment and route it through the rear-facing belt path.

16
00:01:22.720 --> 00:01:26.000
To make it easier, you can press the gray button to extend the lower anchor strap.

17
00:01:26.959 --> 00:01:30.959
Route the strap along the blue line and under the rapid lock lock off.

18
00:01:30.959 --> 00:01:34.239
Attach your lower anchor connector to the lower anchor in your vehicle.

19
00:01:36.480 --> 00:01:42.160
Do the same on both sides. Make sure that your strap lies flat and is not twisted.

20
00:01:43.599 --> 00:01:48.559
Press down on the center of the seat and pull on the free end of the lower anchor strap to tighten.

21
00:01:50.160 --> 00:01:52.480
Close the rapid lock lock off and click it into place.

22
00:01:53.360 --> 00:01:57.680
Test for tightness at the rear-facing belt path. It should not move more than one inch side to side

23
00:01:57.680 --> 00:02:03.279
or front to back. If it does, open the lock off, remove more slack, and then close and test for

24
00:02:03.279 --> 00:02:07.839
tightness again. Recheck the level indicator to ensure it is still in the correct blue zone.

25
00:02:08.639 --> 00:02:11.039
Move the headrest to the proper position for your child.

26
00:02:13.600 --> 00:02:17.759
If not using the infant supports, remove them and store them away. Now you're ready for baby.

27
00:02:18.000 --> 00:02:23.440
Check for proper harness height. Straps should be at or just below your child's shoulders for rear-facing mode.

28
00:02:23.440 --> 00:02:30.160
Buckle your child in and attach the chest clip. Tighten the harness.

29
00:02:31.520 --> 00:02:36.399
Move the chest clip to armpit level. Do the pinch test. You should not be able to pinch

30
00:02:36.399 --> 00:02:40.960
any extra slack at your child's shoulders. Once your little one is properly harnessed,

31
00:02:40.960 --> 00:02:44.080
rotate the seat to the rear-facing position and click it into place.