WEBVTT

1
00:00:00.000 --> 00:00:05.000
♪ Music playing ♪

2
00:00:00.000 --> 00:00:10.000
Hi, I'm Candace from Graco, and I'm going to show you how to install the SnugRide Turn

3
00:00:10.000 --> 00:00:15.880
and Slide Rotating Infant Car Seat with the Lower Anchor Connectors Attachment, or LATCH.

4
00:00:15.880 --> 00:00:20.400
From underneath the base, unhook the lower anchor attachment connectors and remove from

5
00:00:20.400 --> 00:00:24.559
storage position by pulling on the strap.

6
00:00:24.559 --> 00:00:27.340
Place the car seat base flat on the vehicle seat.

7
00:00:27.340 --> 00:00:31.020
Push the base back until the front of the base touches the vehicle seat.

8
00:00:31.020 --> 00:00:35.180
Make sure at least 80% of the base bottom is on the vehicle seat.

9
00:00:35.180 --> 00:00:38.939
Make sure the vehicle is on level ground, then check that the bubble indicator on the

10
00:00:38.939 --> 00:00:40.740
side of the base is level.

11
00:00:40.740 --> 00:00:45.299
The bubble can be positioned anywhere within the dark blue line.

12
00:00:45.299 --> 00:00:49.619
If the bubble indicator is not within the dark blue line, adjust the recline of the

13
00:00:49.619 --> 00:00:50.619
base.

14
00:00:50.619 --> 00:00:55.060
To adjust the recline, squeeze the base recline lever on the front of the base and lift or

15
00:00:55.060 --> 00:00:58.779
lower the base to the appropriate recline.

16
00:00:58.779 --> 00:01:00.540
Recheck the level indicator.

17
00:01:00.540 --> 00:01:06.019
For infants 0 to 3 months, you may prefer more recline, which is the shorter light blue

18
00:01:06.019 --> 00:01:09.779
line.

19
00:01:09.779 --> 00:01:13.260
Open the SnugLock lock off for an easy and quick installation.

20
00:01:13.260 --> 00:01:18.660
Push in the release lever and open the SnugLock arm.

21
00:01:18.660 --> 00:01:23.139
Extend the lower anchor attachment strap to its maximum length by pressing the gray button

22
00:01:23.220 --> 00:01:26.900
and pulling on the strap.

23
00:01:26.900 --> 00:01:31.059
Attach each lower anchor connector to your vehicle's lower anchor points.

24
00:01:31.059 --> 00:01:35.459
You will hear a click when they are connected.

25
00:01:35.459 --> 00:01:39.459
Always check by pulling on them to ensure secure connection.

26
00:01:39.459 --> 00:01:41.820
Make sure they're flat, not twisted.

27
00:01:41.820 --> 00:01:50.739
Pull the adjustment strap and press down firmly on the base to remove any slack.

28
00:01:50.860 --> 00:01:54.300
Push down the SnugLock arm until you hear a firm click.

29
00:01:54.300 --> 00:01:57.900
This locks the seatbelt securely in place.

30
00:01:57.900 --> 00:02:02.300
Grab the sides of the base where the seatbelt is and push and pull the base from side to

31
00:02:02.300 --> 00:02:03.980
side and front to back.

32
00:02:03.980 --> 00:02:06.620
It should not move more than one inch.

33
00:02:06.620 --> 00:02:11.860
Now, let's use the turn and slide to securely place your infant car seat attached to the

34
00:02:11.860 --> 00:02:12.860
base.

35
00:02:12.860 --> 00:02:16.979
To rotate the car seat base, pull on the turn lever and rotate the seat in the direction

36
00:02:16.979 --> 00:02:17.979
of the lever.

37
00:02:18.100 --> 00:02:21.220
The turn levers are located on each side of the car seat.

38
00:02:21.220 --> 00:02:26.179
You only need to use one lever to rotate the car seat.

39
00:02:26.179 --> 00:02:30.419
Attach the car seat by placing the rear edge of the car seat near the two channels in the

40
00:02:30.419 --> 00:02:31.419
base.

41
00:02:31.419 --> 00:02:35.580
Then slide the car seat toward the back of the channels until you hear a click.

42
00:02:35.580 --> 00:02:38.380
You can pull on the seat to make sure it is locked.

43
00:02:38.380 --> 00:02:42.220
Once the seat is secured, rotate the seat into rear-facing position.

44
00:02:42.220 --> 00:02:46.220
You will hear another click when the seat is securely locked into place.

45
00:02:46.220 --> 00:02:50.020
Always check the green lock indicator near the front of the base to confirm the seat

46
00:02:50.020 --> 00:02:52.020
is securely locked before every ride.

47
00:02:52.020 --> 00:02:56.339
If it is not green, try to lift up on the seat to ensure that the seat is locked into

48
00:02:56.339 --> 00:02:59.500
the base and that the indicator is green.

49
00:02:59.500 --> 00:03:04.380
To rotate the car seat base, pull on the turn lever again and rotate the seat in the direction

50
00:03:04.380 --> 00:03:05.380
of the lever.

51
00:03:05.380 --> 00:03:09.399
When the seat is facing you from the front of the car seat, squeeze the release lever

52
00:03:09.399 --> 00:03:12.779
and slide the car seat towards you and away from the base.

53
00:03:12.779 --> 00:03:13.699
It's that easy.